久久久久久久999_99精品久久精品一区二区爱城_成人欧美一区二区三区在线播放_国产精品日本一区二区不卡视频_国产午夜视频_欧美精品在线观看免费

標題: STM32F103ZET6串口1應用代碼 [打印本頁]

作者: irisice008 時間: 2019-5-27 22:48
標題: STM32F103ZET6串口1應用代碼
#include "usart1.h"
#define RX_BUFER_SIZE 32
u8 rx_buffer[RX_BUFER_SIZE] = {0};
u8 *rx_bufferP = rx_buffer;
u8 Usart_RecvIng = 0;
u8 Usart_RecvEnd = 0;
u8 Usart_Monitor = 0;
void My_USART1_Init(void)
{
  GPIO_InitTypeDef  GPIO_InitStructure;
  USART_InitTypeDef  USART_InitStructure;
  NVIC_InitTypeDef NVIC_InitStructure;

  RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA, ENABLE);    //使能PA端口時鐘
  RCC_APB2PeriphClockCmd(RCC_APB2Periph_USART1, ENABLE);    //使能USART1端口時鐘

  GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP;
  GPIO_InitStructure.GPIO_Pin = GPIO_Pin_9;
  GPIO_InitStructure.GPIO_Speed = GPIO_Speed_10MHz;
  GPIO_Init(GPIOA, &GPIO_InitStructure);          //初始化GPIOA_Pin_9

  GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IN_FLOATING;
  GPIO_InitStructure.GPIO_Pin = GPIO_Pin_10;
  GPIO_InitStructure.GPIO_Speed = GPIO_Speed_10MHz;
  GPIO_Init(GPIOA, &GPIO_InitStructure);          //初始化GPIOA_Pin_10

  //設置NVIC中斷分組
  NVIC_PriorityGroupConfig(NVIC_PriorityGroup_2); //設置NVIC中斷分組2：2位搶占優先級，2位響應優先級0-3;

  NVIC_InitStructure.NVIC_IRQChannel =  USART1_IRQn;
  NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
  NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 1; //搶占優先級1
  NVIC_InitStructure.NVIC_IRQChannelSubPriority = 1;  //子優先級1
  NVIC_Init(&NVIC_InitStructure); //設置中斷優先級，根據指定的參數初始化VIC寄存器

  USART_InitStructure.USART_BaudRate = 512000;
  USART_InitStructure.USART_HardwareFlowControl = USART_HardwareFlowControl_None;
  USART_InitStructure.USART_Mode = USART_Mode_Rx | USART_Mode_Tx;
  USART_InitStructure.USART_Parity = USART_Parity_No;
  USART_InitStructure.USART_StopBits = USART_StopBits_1 ;
  USART_InitStructure.USART_WordLength = USART_WordLength_8b;
  USART_Init(USART1, &USART_InitStructure); //初始化串口1

  USART_ITConfig(USART1, USART_IT_RXNE, ENABLE); //開啟串口接收中斷
  USART_Cmd(USART1, ENABLE); //使能USART1
}

void USART1_SendChar(u8 ch)
{
  while(USART_GetFlagStatus(USART1,USART_FLAG_TC)==RESET); //must have
  USART_SendData(USART1, ch);
}

void USART1_SendStr(u8* str)
{
while(*str)
{
  while(USART_GetFlagStatus(USART1,USART_FLAG_TC)==RESET);  //must have
  USART_SendData(USART1, *str++);
}
}
void USART1_IRQHandler(void)
{
  if (USART_GetITStatus(USART1, USART_IT_RXNE) != RESET)
  {
if(!Usart_RecvEnd)
{
Usart_Monitor = 1;
*rx_bufferP++ = USART_ReceiveData(USART1);
*rx_bufferP = '\0'; //沒有此語句也可以
Usart_RecvIng = 1;
}
  }
  if(USART_GetFlagStatus(USART1,USART_FLAG_ORE) == SET) //溢出處理
  {
USART_ReceiveData(USART1);
   USART_ClearFlag(USART1,USART_FLAG_ORE);
  }
  USART_ClearFlag(USART1,USART_IT_RXNE); //一定要清除接收中斷
}

Template_Lib_USART.7z

178.83 KB, 下載次數: 34, 下載積分: 黑幣 -5

歡迎光臨 (http://m.zg4o1577.cn/bbs/)

<rt id="ouos8"></rt>