久久久久久久999_99精品久久精品一区二区爱城_成人欧美一区二区三区在线播放_国产精品日本一区二区不卡视频_国产午夜视频_欧美精品在线观看免费

標題: 富斯8通接收機單片機源碼 [打印本頁]

作者: bjgaocl 時間: 2019-9-21 16:14
標題: 富斯8通接收機單片機源碼
#include<reg52.h>
#include<intrins.h>
//#define GUDING                               //固定失控值/自由自定
#define u8 unsigned char
#define u16 unsigned int             //*******晶振設定*******//
#define u32 unsigned long int       //內置 12Mhz 16Mhz 24Mhz//
#define WZ12Mhz             1                      // 0       1    0          0       //
#define WZ16Mhz             0                      // 0       0       1          0       //
#define WZ24Mhz             0                      // 0       0       0          1       //
sfr IAP_DATA=0xc2;                               //**********************//
sfr IAP_ADDRH=0xc3;
sfr IAP_ADDRL=0xc4;
sfr IAP_CMD=0xc5;
sfr IAP_TRIG=0xc6;
sfr IAP_CONTR=0xc7;
sfr P1M0=0x92;//單片機IO口配置寄存器地址
sfr P3M0=0xb2;
//定義指示燈
sbit LED=P3^0;
sbit bind=P3^7;
//定義8個通道輸出
sbit CH1=P1^7;
sbit CH2=P1^6;
sbit CH3=P1^5;
sbit CH4=P1^4;
sbit CH5=P1^3;
sbit CH6=P1^2;
sbit CH7=P1^1;
sbit CH8=P1^0;
//定義無線模塊的管腳
sbit GIO=P3^2;
sbit MDI=P3^3;
sbit SCK=P3^4;
sbit CSN=P3^5;
u8 code A7105_regs[]={                      //模塊寄存器設定表
0xff, 0x42, 0x00, 0x14, 0x00, 0xff, 0xff ,0x00, 0x00, 0x00, 0x00, 0x01, 0x21, 0x05, 0x00, 0x50,
0x9e, 0x4b, 0x00, 0x02, 0x16, 0x2b, 0x12, 0x00, 0x62, 0x80, 0x80, 0x00, 0x0a, 0x32, 0xc3, 0x0f,
0x13, 0xc3, 0x00, 0xff, 0x00, 0x00, 0x3b, 0x00, 0x17, 0x47, 0x80, 0x03, 0x01, 0x45, 0x18, 0x00,
0x01, 0x0f, 0xff,
};
u8 code tx_channels[16][16]={             //跳頻表
  {0x0a, 0x5a, 0x14, 0x64, 0x1e, 0x6e, 0x28, 0x78, 0x32, 0x82, 0x3c, 0x8c, 0x46, 0x96, 0x50, 0xa0},
  {0xa0, 0x50, 0x96, 0x46, 0x8c, 0x3c, 0x82, 0x32, 0x78, 0x28, 0x6e, 0x1e, 0x64, 0x14, 0x5a, 0x0a},
  {0x0a, 0x5a, 0x50, 0xa0, 0x14, 0x64, 0x46, 0x96, 0x1e, 0x6e, 0x3c, 0x8c, 0x28, 0x78, 0x32, 0x82},
  {0x82, 0x32, 0x78, 0x28, 0x8c, 0x3c, 0x6e, 0x1e, 0x96, 0x46, 0x64, 0x14, 0xa0, 0x50, 0x5a, 0x0a},
  {0x28, 0x78, 0x0a, 0x5a, 0x50, 0xa0, 0x14, 0x64, 0x1e, 0x6e, 0x3c, 0x8c, 0x32, 0x82, 0x46, 0x96},
  {0x96, 0x46, 0x82, 0x32, 0x8c, 0x3c, 0x6e, 0x1e, 0x64, 0x14, 0xa0, 0x50, 0x5a, 0x0a, 0x78, 0x28},
  {0x50, 0xa0, 0x28, 0x78, 0x0a, 0x5a, 0x1e, 0x6e, 0x3c, 0x8c, 0x32, 0x82, 0x46, 0x96, 0x14, 0x64},
  {0x64, 0x14, 0x96, 0x46, 0x82, 0x32, 0x8c, 0x3c, 0x6e, 0x1e, 0x5a, 0x0a, 0x78, 0x28, 0xa0, 0x50},
  {0x50, 0xa0, 0x46, 0x96, 0x3c, 0x8c, 0x28, 0x78, 0x0a, 0x5a, 0x32, 0x82, 0x1e, 0x6e, 0x14, 0x64},
  {0x64, 0x14, 0x6e, 0x1e, 0x82, 0x32, 0x5a, 0x0a, 0x78, 0x28, 0x8c, 0x3c, 0x96, 0x46, 0xa0, 0x50},
  {0x46, 0x96, 0x3c, 0x8c, 0x50, 0xa0, 0x28, 0x78, 0x0a, 0x5a, 0x1e, 0x6e, 0x32, 0x82, 0x14, 0x64},
  {0x64, 0x14, 0x82, 0x32, 0x6e, 0x1e, 0x5a, 0x0a, 0x78, 0x28, 0xa0, 0x50, 0x8c, 0x3c, 0x96, 0x46},
  {0x46, 0x96, 0x0a, 0x5a, 0x3c, 0x8c, 0x14, 0x64, 0x50, 0xa0, 0x28, 0x78, 0x1e, 0x6e, 0x32, 0x82},
  {0x82, 0x32, 0x6e, 0x1e, 0x78, 0x28, 0xa0, 0x50, 0x64, 0x14, 0x8c, 0x3c, 0x5a, 0x0a, 0x96, 0x46},
  {0x46, 0x96, 0x0a, 0x5a, 0x50, 0xa0, 0x3c, 0x8c, 0x28, 0x78, 0x1e, 0x6e, 0x32, 0x82, 0x14, 0x64},
  {0x64, 0x14, 0x82, 0x32, 0x6e, 0x1e, 0x78, 0x28, 0x8c, 0x3c, 0xa0, 0x50, 0x5a, 0x0a, 0x96, 0x46},
};
u32 id;                                                             //對碼ID
u8 chanrow,chancol,chanoffset,channel;
u8 txid[21]={0,0,0,0,0,220,5,220,5,232,3,220,5,220,5,220,5,220,5,220,5};
u8 packet[21];
u8 Htemp[8]={5,5,3,5,5,5,5,5};
u8 Ltemp[8]={220,220,232,220,220,220,220,220};
u8 ch=0;
u16 mss;
bit hch,cb;
#if WZ12Mhz                               //延時定義
void Delay1ms(){             //@12.000MHz
      unsigned char i, j;
      _nop_();
      _nop_();
      i = 10;
      j = 83;
      do
      {
            while (--j);
      } while (--i);
}
#elif WZ16Mhz
void Delay1ms(){             //@18.432MHz
      unsigned char i, j;
      _nop_();
      _nop_();
      i = 18;
      j = 234;
      do{
            while (--j);
      } while (--i);
}
#elif WZ24Mhz
void Delay1ms(){             //@24.000MHz
      unsigned char i, j;
      _nop_();
      _nop_();
      i = 24;
      j = 84;
      do{
            while (--j);
      } while (--i);
}
#else
void Delay1ms()       {             //@5.5296MHz
      unsigned char i, j;
      _nop_();
      _nop_();
      i = 6;
      j = 93;
      do{
            while (--j);
      } while (--i);
}
#endif

附件為完整代碼

flysky.rar (3.79 KB, 下載次數: 146)

作者: zhouyong2 時間: 2020-2-17 15:11
太感謝樓主了！！！

作者: kkku 時間: 2020-4-2 23:57
太感謝樓主了！！！

作者: kkku 時間: 2020-4-2 23:58
感謝樓主!!!！！！

作者: spyhooky 時間: 2020-4-3 13:07
太感謝樓主了

作者: 太陽黑子1 時間: 2020-4-3 18:32
太感謝了！

作者: 1445794010 時間: 2020-4-15 22:21
感謝樓主，這是二代的嗎？

作者: zxhf 時間: 2020-5-20 09:18
看著好像沒有sbus這類的協議

作者: 天際遨游 時間: 2020-6-6 00:14
好啊我需要！

作者: 大漠游民 時間: 2020-10-24 17:19
太感謝樓主了！

作者: b294303665 時間: 2020-10-27 14:29
不錯不錯，謝謝分享

歡迎光臨 (http://m.zg4o1577.cn/bbs/)