日韩久久一区二区,91亚洲福利,久草免费在线

#include "ina219.h"
void INA_REG_Write(unsigned char reg,unsigned int data);
#ifdef INA_INSIDE_IIC
void INA_IIC_Delay()
{unsigned char x;
for(x=1;x>0;x--)
{
__NOP();__NOP();__NOP();__NOP();__NOP();
}
}
void INA_IIC_INIT(void) //IIC初始化
{
GPIO_InitTypeDef GPIO_INIT;
RCC_APB2PeriphClockCmd(IIC_RCC,ENABLE);
GPIO_INIT.GPIO_Mode=GPIO_Mode_Out_PP;
GPIO_INIT.GPIO_Pin=IIC_SDA | IIC_SCL;
GPIO_INIT.GPIO_Speed=GPIO_Speed_50MHz;
GPIO_Init(IIC_PORT,&GPIO_INIT);
IIC_SDA_H;
IIC_SCL_H;
}
void INA_IIC_SDA_OUT(void) //SDA配置為輸出
{
GPIO_InitTypeDef GPIO_INIT;
GPIO_INIT.GPIO_Mode=GPIO_Mode_Out_PP;
GPIO_INIT.GPIO_Pin=IIC_SDA ;
GPIO_INIT.GPIO_Speed=GPIO_Speed_50MHz;
GPIO_Init(IIC_PORT,&GPIO_INIT);
}
void INA_IIC_SDA_IN(void) //SDA配置為輸入
{
GPIO_InitTypeDef GPIO_INIT;
GPIO_INIT.GPIO_Mode=GPIO_Mode_IPU;
GPIO_INIT.GPIO_Pin=IIC_SDA ;
GPIO_INIT.GPIO_Speed=GPIO_Speed_50MHz;
GPIO_Init(IIC_PORT,&GPIO_INIT);
}
void INA_IIC_Start(void) //開始信號
{
IIC_SDA_H;
IIC_SCL_H;
INA_IIC_Delay();
IIC_SDA_L;
INA_IIC_Delay();
IIC_SDA_L;
}
void INA_IIC_Stop(void ) //結束信號
{
IIC_SDA_L;
IIC_SCL_H;
INA_IIC_Delay();
IIC_SDA_H;
INA_IIC_Delay();
IIC_SCL_L;
IIC_SCL_H;
IIC_SDA_H;
}
bool INA_IIC_ACK_Read(void) //讀取應答信號
{
bool ack;
IIC_SDA_H;
INA_IIC_SDA_IN();
IIC_SCL_H;
INA_IIC_Delay();
if(IIC_SDA_READ() == SET) ack=false;
else ack=true;
IIC_SCL_L;
INA_IIC_SDA_OUT();
return ack;
}
void INA_IIC_ACK_Send(bool ack) //發送應答信號
{
IIC_SCL_L;
if(ack == true)
IIC_SDA_L;
else IIC_SDA_H;
IIC_SCL_H;
INA_IIC_Delay();
IIC_SCL_L;
}
void INA_IIC_Send_Byte(unsigned char byte) //IIC發送一位數據
{
unsigned char i;
IIC_SCL_L;
for(i=0;i<8;i++)
{
if(byte & 0x80 ) IIC_SDA_H;
else IIC_SDA_L;
IIC_SCL_H;
INA_IIC_Delay();
IIC_SCL_L;
INA_IIC_Delay();
byte<<=1;
}
INA_IIC_ACK_Read();
}
unsigned char INA_IIC_Read_Byte(void) //IIC讀取一位數據
{
unsigned char i,byte=0;
INA_IIC_SDA_IN();
for(i=0;i<8;i++)
{
IIC_SCL_H;
byte<<=1;
if(IIC_SDA_READ() == SET) byte |= 0x01;
else byte &= 0xFE;
IIC_SCL_L;
INA_IIC_Delay();
}
INA_IIC_SDA_OUT();
return byte;
}
#endif
void INA_Read_Byte_s(unsigned char reg,unsigned char *data) //讀兩位數據
{
INA_IIC_Start();
INA_IIC_Send_Byte(INA219_ADDRESS); //發送INA219地址s
INA_IIC_Send_Byte(reg);
INA_IIC_Start();
INA_IIC_Send_Byte(INA219_ADDRESS+0x01); //設置iic為讀模式
*data=INA_IIC_Read_Byte();
data++;
INA_IIC_ACK_Send(1);
*data=INA_IIC_Read_Byte();
INA_IIC_ACK_Send(0);
INA_IIC_Stop();
}
void INA_REG_Write(unsigned char reg,unsigned int data) //寫寄存器測試成功
{
unsigned char data_temp[2];
data_temp[0]=(unsigned char )(data>>8);
data_temp[1]=(unsigned char )(data & 0xFF);
INA_IIC_Start();
INA_IIC_Send_Byte(INA219_ADDRESS); //發送INA219地址
INA_IIC_Send_Byte(reg); //發送寄存器地址
INA_IIC_Send_Byte(data_temp[0]); //發送高8位數據
data++;
INA_IIC_Send_Byte(data_temp[1]) ; //發送低8位數據
INA_IIC_Stop();
}
void INA_Init(void )
{
INA_IIC_INIT();
INA_REG_Write(INA219_REG_CONFIG,INA219_CONFIG_value);
INA_REG_Write(INA219_REG_CALIBRATION,INA_CAL);
}
unsigned int INA_GET_Voltage_MV(void) //獲取電壓（單位：mv）
{
unsigned char data_temp[2];
INA_Read_Byte_s(0x02,data_temp);
return (int)((((data_temp[0]<<8)+data_temp[1]) >> 3)*4); //右移3為去掉：bit2，CNVR，OVF三位，再乘以 4MV (官方文檔規定)，得到當前總線的電壓值
}
unsigned int INA_GET_Current_MA(void) //獲取電流（單位：mA）
{
unsigned char data_temp[2];
INA_REG_Write(INA219_REG_CONFIG,INA219_CONFIG_value);
INA_Read_Byte_s(INA219_REG_CURRENT,data_temp);
return (int)((((data_temp[0]<<8)+data_temp[1]))*IAN_I_LSB); //得到寄存器的值在乘以每位對應的值（IAN_I_LSB）得到實際的電流
}
unsigned int INA_GET_Power_MW(void) //獲取當前功率（單位：mw）
{
unsigned char data_temp[2];
INA_Read_Byte_s(INA219_REG_POWER,data_temp);
return (int)(((data_temp[0]<<8)+data_temp[1])*INA_Power_LSB); //得到寄存器的值在乘以每位對應的值（INA_Power_LSB）得到實際的功率
}

復制代碼

#include <stdio.h>
#include <string.h>
#include "stm32f10x.h"
#include "stm32f10x_it.h"
#include "io.h"
//#include "key.h"
#include "delay.h"
//#include "timer.h"
#include "usart.h"
#include "adc.h"
//#include "24cxx.h"
//#include "menu.h"
#include "ina219.h"
void Uart1_PutString(char* buf,u8 len );
u8 Uart1_PutChar(u8 ch);
u8 Uart1_recChar(void);
void judge_command(void);
void manul_test(void);
void auto_test(void);
void debug_test(void);
void emerg(void);
//*DO01ON#----6
//DO01OFF---7
//uchar command_data[7];
//uchar RX_dat;
int STEP_flag;
//u8 count;
void SysInit (void)
{
SystemInit();//系統時鐘配置配置為72MHZ
delay_init();//延時函數初始化
NVIC_PriorityGroupConfig(NVIC_PriorityGroup_2); //設置NVIC中斷分組2:2位搶占優先級，2位響應優先級
IO_Init();
//TIM2_Int_Init(99,71);//1Mhz的計數頻率，計數到100為0.1ms
//TIM3_Int_Init(99,7199);//10Khz的計數頻率，計數到100為10ms
Adc_Init();
Usart_Init();
INA_Init();
}
int main(void)
{
// int flag1,flag2,flag3,flag4;
//flag1=0,flag2=0,flag3=0,flag4=0;
//float LDR1Adc,LDR2Adc;
SysInit();
delay_ms(1000);
}

復制代碼

久久久久久久999_99精品久久精品一区二区爱城_成人欧美一区二区三区在线播放_国产精品日本一区二区不卡视频_国产午夜视频_欧美精品在线观看免费