久久久久久久999_99精品久久精品一区二区爱城_成人欧美一区二区三区在线播放_国产精品日本一区二区不卡视频_国产午夜视频_欧美精品在线观看免费

標題: 官網AN1299對應的工程,dsPIC33CK芯片,編譯不成功,怎么辦? [打印本頁]

作者: yermsir    時間: 2022-3-3 23:00
標題: 官網AN1299對應的工程,dsPIC33CK芯片,編譯不成功,怎么辦?
在Microchip官網下載了AN1299對應工程,芯片是dsPIC33CK芯片的,編譯不通過。詳細情況請看截圖。
1.截圖的左側工程的文件是灰色。但是雙擊能夠打得開。
2.編譯報錯,都是生成.o格式的文件報錯。
nbproject/Makefile-MCLV2.mk:166: recipe for target 'build/MCLV2/production/_ext/1360926148/adc.o' failed

捕獲.JPG (189.05 KB, 下載次數: 98)

捕獲.JPG

作者: yermsir    時間: 2022-3-5 14:44
有沒有大神幫忙看看?
作者: umer94    時間: 2023-10-18 00:50


I am using DSPIC33CK32MC102 , I have code and its hex file ready. I made the connections for the controller those are as follows:

    Pullup resistor of 5.5 kΩ for MCLR pin and 100 Ω between pullup and MCLR pin
    0.1 uF ceramic capacitor between VDD and VSS as told in datasheet

I am using PICKIT 4 for programming where the pin are connected as follows:

    MCLR = pin 27
    VDD = pin 20
    VSS = pin 19
    PGD = pin17
    PGC = pin 18

The connections are perfect and no wire is bas solder

When I plug USB to laptop and click "connect" it says following error and connects anyhow:

    Target Device ID (0x0) is an Invalid Device ID. Please check your connections to the Target Device. UDID1 = 000000 UDID2 = 000000 UDID3 = 000000 UDID4 = 000000 UDID5 = 000000

After this, when I click "program" it gives following error:

    Programming did not complete. You are trying to change protected boot memory. In order to do this you must select the "Boot, Secure and General Segments" option on the debug tool Secure Segment properties page.

Then in settings > secure segment > segments to be programmed > Boot, General and Config segment is selected.

After this, when I click "program" it gives following error:

    [ Pgm ] at 0x0, expected 0x00040200, got 0x00000000. You have set the program speed to Normal. The circuit on your board may require you to slow the speed down. Please change the setting in the tool properties to low and try the operation again. Programming did not complete.

Then in settings > PICKIT4 tool options > programming speed > low selected.

After this, when I click "program" it gives following error:

    [ Pgm ] at 0x0, expected 0x00040200, got 0x00000000. Programming did not complete.

Also this approach:

    Target Device ID (0x0) is an Invalid Device ID. Please check your connections to the Target Device. UDID1 = 000000 UDID2 = 000000 UDID3 = 000000 UDID4 = 000000 UDID5 = 000000

After this I click "erase" followed by "read" it says:

    Read complete Warning: Debug bit is set on target image. This may not run correctly in production.

Now if I hit "program" it says following warning:

    Memory Image changed do you wish to continue programming device

Selecting yes it programs successfully, but I don't know what has he program its more like a blank file is been programmed.

The following memory area(s) will be programmed:

    program memory: start address = 0x0, end address = 0x5eff configuration memory Programming/Verify complete 2023-08-02 15:58:58 +0530 - Programming complete *** Hold In Reset mode is enabled ***
help me,
is it
hardware error
How i can rid of it.

作者: umer94    時間: 2023-10-18 15:15
我有與上面鏈接相同的問題,
有什么可以幫助我的嗎




歡迎光臨 (http://m.zg4o1577.cn/bbs/) Powered by Discuz! X3.1
主站蜘蛛池模板: 国产一区二区在线看 | 久久香蕉精品 | 手机在线免费看av | 免费看黄色录像 | 亚洲看片 | 无套内谢的新婚少妇国语播放 | 黄色小视频在线观看 | 久久精品区 | 亚洲国产成人精品女人久久久 | 国产在线小视频 | 精品久久影院 | 精品一二区 | 天天操夜夜骑 | 欧美一区二区在线播放 | 日日操夜夜爽 | 在线免费黄色网址 | 色影视 | 国产美女福利 | 国产中文字幕在线播放 | 欧美日韩在线视频观看 | 亚洲美女网站 | 欧美日韩一区二 | 亚洲在线视频观看 | 国产日韩精品一区二区 | 久久久久久一区 | 国产原创精品 | 69久久久 | 欧美日韩一区在线观看 | 在线不卡视频 | 久久天天 | 成人免费视频国产免费 | 欧美8888| 能看毛片的网站 | 欧美激情网 | 欧美激情网 | 欧美日本精品 | 午夜视频免费 | 亚洲区视频| 少妇高潮久久久久久潘金莲 | 久热在线 | 日本激情网 |