STM32環境檢測系統設計可顯示PM2.5及溫濕度

ID:198608 · 發表于 2017-10-20 21:51

采用dht11溫濕度傳感器，和pm2.5傳感器，用tft液晶屏顯示
做出來的實物圖：

單片機源程序如下:

#include "delay.h"
#include "sys.h"
#include "lcd.h"
#include "usart.h"
#include "led.h"
#include "dht11.h"
#include "ds18b20.h"
#include "adc.h"
unsigned char hjjc[72*6] = // ASCII
{
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xE0,0xE7,0x1F,0x58,0x98,0x00,0x40,0x80,0x00,0x40,0x40,0x00,
0x40,0x40,0x00,0xC0,0xE3,0x00,0x78,0x60,0x00,0x40,0x50,0x02,0x40,0x50,0x04,0x40,0x48,0x08,0x40,0x46,0x10,0xC0,0x43,0x30,
0x30,0x42,0x20,0x8C,0x41,0x00,0x00,0x40,0x00,0x00,0x40,0x00,0x00,0x40,0x00,0x00,0x40,0x00,0x00,0x00,0x00,0x00,0x00,0x00,/*"環",0*/
…………限于本文篇幅余下代碼請從51黑下載附件…………
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x78,0x00,0xC4,0x00,0x86,0x01,0x86,0x01,0x86,0x01,0x80,0x01,0xC0,0x00,
0x70,0x00,0x80,0x01,0x00,0x01,0x00,0x03,0x06,0x03,0x06,0x03,0x06,0x03,0x84,0x01,0xF8,0x00,0x00,0x00,0x00,0x00,0x00,0x00,/*"3",4*/
};
//ALIENTEK戰艦STM32開發板實驗13
//TFTLCD顯示實驗
//技術支持：www.openedv.com
//廣州市星翼電子科技有限公司
extern u8 Res;
extern u8 Res3;
int tcont,cont=5;;
extern __IO u16 ADC_ConvertedValue[4];
void numstring(uint16_t Xpos, uint16_t Ypos, u32 mun,u16 BL)
{
shuzi24(Xpos, Ypos, &ASCII_Table24N[0+48*(mun/10)], BL);
shuzi24(Xpos+12*1, Ypos, &ASCII_Table24N[0+48*(mun%10)], BL);
}
void numstrings(uint16_t Xpos, uint16_t Ypos, u32 mun,u16 BL)
{
shuzi24(Xpos, Ypos, &ASCII_Table24N[0+48*(mun/1000)], BL);
shuzi24(Xpos+12*1, Ypos, &ASCII_Table24N[0+48*(mun%1000/100)], BL);
shuzi24(Xpos+12*2, Ypos, &ASCII_Table24N[0+48*(mun%1000%100/10)], BL);
shuzi24(Xpos+12*3, Ypos, &ASCII_Table24N[0+48*(mun%1000%100%10)], BL);
}
void zifuchar(uint16_t Xpos, uint16_t Ypos, u8 * mun,u16 BL)
{
shuzi24(Xpos, Ypos, mun, BL);
shuzi24(Xpos+12*1, Ypos, mun+48*1, BL);
shuzi24(Xpos+12*2, Ypos, mun+48*2, BL);
shuzi24(Xpos+12*3, Ypos, mun+48*3, BL);
shuzi24(Xpos+12*4, Ypos, mun+48*4, BL);
}
int main(void)
{
u8 humidity;
u8 temp;
short temperature;
delay_init(); //延時函數初始化
NVIC_Configuration(); //設置NVIC中斷分組2:2位搶占優先級，2位響應優先級
uart_init(115200); //串口初始化為9600
LED_Init();
Adc_Init(); //adc8
// USART3_Config();
LCD_Init();
POINT_COLOR=RED;
wordstring(40, 10,hjjc,6,RED); //環境監測系統
wordstring(10, 150,wd,2,RED); //溫度
wordstring(10, 180,sd,2,RED); // 濕度
while(DS18B20_Init());
while(1)
{
temperature=DS18B20_Get_Temp();
if(temperature<0)
{
shuzi24(55, 150, fh, RED); //顯示負號
temperature=-temperature; //轉為正數
}else shuzi24(55, 150, qk, RED); //去掉負號
//
DHT11_Read_Data(&temp,&humidity); //讀取溫濕度值
numstring(70, 150,temperature/10,BRED); //顯示溫度
wordstring(100, 150,wd+72*2,1,RED); //溫度符號
numstring(70, 180,humidity,BRED); //顯示濕度
shuzi24(100, 180,sdfh,RED);shuzi24(112, 180,sdfh+48,RED);shuzi24(124, 180,sdfh+96,RED); //濕度符號
zifuchar(5, 210,PM,RED);
shuzi24(70, 210,&ASCII_Table24N[0+48*(Get_Adc_Average(1)/620)], BRED); //毫克量
zifuchar(90, 210,MG,RED);
delay_ms(200);
}
}
/*代碼說明*/
/*main函數掃描按鍵顯示放電預設值
* 定時器3 放電定時
* 定時器4 ad掃描
*/